Caravan Panels · Buying guide
Choosing a replacement caravan A-frame cover starts with the shape and measurements of the cover already fitted, not just your caravan's badge. Compare the tapered outline, raised sections, openings and fixing points before ordering.
This guide covers the moulded exterior cover over the caravan's A-frame area, not a soft hitch cover or a structural chassis component. It is an identification and buying guide, not a removal or fitting manual.
The quick rule: a similar outline is not proof of fit. Check the length, widths, profile and cut-outs, and confirm that the correct replacement will leave the required clearance around the towing equipment.
1. Record your caravan details
Write down the manufacturer, exact model and year, plus any safely visible reference on the existing cover. Take a photograph of the complete front of the caravan and its A-frame area.
Start with the range for your caravan manufacturer, but compare the individual cover with your existing part. Do not assume every model from one brand uses the same cover. Product numbers such as “001” or “011” identify listings, not model years or guaranteed fitment.
2. Use this measurement checklist
Record measurements in millimetres on a labelled sketch. Mark the caravan end and hitch end clearly. Measure straight between labelled points rather than following a curved surface unless the listing specifically uses a surface measurement.
- Overall length: measure between the two outer ends, noting any lip or extended section included.
- Width at each end: record the broad caravan-end width and the narrower hitch-end width separately.
- Intermediate widths: note where the sides change angle or curve, with the distance of each measuring point from a labelled end.
- Profile and height: record accessible raised sections, steps, edge returns and the depth of the moulding. Mark concealed details as unconfirmed.
- Cut-outs: sketch each round opening, slot, notch and edge cut-out. Record its size and position from two labelled edges.
- Fixing points: record the number and positions of visible holes or mounting tabs, measuring to hole centres where accessible.
- Bodywork junction: show how the broad end meets the caravan's front panel and any adjacent mouldings.
Only measure what is safely accessible with the caravan secured. Do not release the handbrake, disconnect equipment or disturb the cover to obtain a measurement. If damage or missing sections make a measurement uncertain, say so rather than guessing. Product photos are not scale drawings.
3. Compare the outline and moulded profile

Compare the full shape from the same viewing direction: broad end, narrow end, side taper, raised sections and edge returns. A cover can have similar overall dimensions but different openings or a different underside profile.

4. Check openings and equipment clearance
Photograph how the existing cover sits around the handbrake, jockey wheel, coupling area and any other equipment. Record which openings correspond to which components, rather than assuming that a similar-looking slot serves the same purpose on another cover.
A replacement must not obstruct the operation or movement of towing equipment. Ask a competent caravan technician to confirm suitability and the clearances required for your installation. Do not reposition, modify or disconnect towing or braking equipment to make an unsuitable cover fit.
If equipment has been changed or accessories added, mention this when asking about compatibility. A matching caravan model alone does not establish clearance for a modified arrangement.
5. Confirm material, colour and supplied fittings
Read each listing for its stated material, finish and whether the part is an original or aftermarket replacement. Do not assume every A-frame cover in one manufacturer's range has the same construction.
Check the stated colour and ask about the finish if matching is important. Existing bodywork may have aged or been repaired, and a screen photo cannot guarantee a colour match. Confirm whether fixings or caps are included instead of assuming the existing fittings will transfer.
6. Ask before trimming, drilling or fitting
Do not assume a replacement cover is pre-drilled or that trimming is permitted. If alteration appears necessary, ask about the exact product's permitted changes, mounting and fitting requirements before buying.
Have damaged mounting points or adjacent bodywork assessed before installation. Do not treat a cosmetic cover as a repair for structural damage. Do not stand on the cover unless its manufacturer expressly confirms it is designed for that use.
Check the supplied part's condition and fit before painting, cutting, drilling or permanently fixing it. Use the product-specific fitting guidance and a competent installer where required.
7. Send a useful set of photos
Include an overall view from above where safely possible, a side view showing the raised profile, close-ups of each cut-out and fixing point, and a photo of how the cover meets the caravan body. Include any visible part reference and label which end faces the hitch.
Send a written measurement sketch alongside the photos. If the cover is missing, photograph the exposed area without disturbing any equipment and explain which dimensions cannot be confirmed.
Before you order: your comparison pack
Keep your caravan make, model and year; labelled dimensions; photos; existing part reference if available; and the candidate product link together. Add specific questions about profile, openings, fixing points, finish and equipment clearance.
Contact Caravan Panels with these details if you need help narrowing down the options. A brand name or similar photo alone is not enough to confirm fitment.
Find your replacement A-frame cover
Example ranges include Swift Caravan A-Frame Covers and Elddis Caravan A-Frame Covers. If you own another make, contact us with your caravan details rather than assuming these examples fit.
Compare the actual cover, confirm the uncertain details and resolve fitting questions before ordering. A careful check now is better than discovering a mismatch after alteration.